AV-Comparatives: Business Security Test March-April 2022 – Factsheet

[harlan4096]

Introduction

This is a short fact sheet for our Business Main-Test Series, containing the results of the Business Malware Protection Test (March) and Business Real-World Protection Test (March-April). The full report, including the Performance Test and product reviews, will be released in July.

To be certified in July 2022 as an “Approved Business Product” by AV-Comparatives, the tested products must score at least 90% in the Malware Protection Test, with zero false alarms on common business software, and an FP rate on non-business files below the Remarkably High threshold. Additionally, products must score at least 90% in the overall Real-World Protection Test (i.e. over the course of four months), with less than one hundred false alarms on any clean software/websites, and zero false alarms on common business software. Tested products must also avoid major performance issues (impact score must be below 40) and have fixed all reported bugs in order to gain certification.

Please note that the results of the Business Main-Test Series cannot be compared with the results of the Consumer Main-Test Series, as the tests are done at different times, with different sets, different settings, etc.

Tested Products

The following products were tested under Windows 10 64-bit and are included in this factsheet:

Information about additional third-party engines/signatures used by some of the products: Acronis, Cisco, Cybereason, G Data, Trellix and VIPRE use the Bitdefender engine (in addition to their own protection features). VMware uses the Avira engine (in addition to their own protection features). G Data’s OutbreakShield is based on Cyren.

In business environments, and with business products in general, it is usual for products to be configured by the system administrator, in accordance with vendor’s guidelines, and so we invited all vendors to configure their respective products.

Only a few vendors provide their products with optimal default settings which are ready to use, and did therefore not change any settings.

Please keep in mind that the results reached in the Enterprise Main-Test Series were only achieved by applying the respective product configurations described here. Any setting listed here as enabled might be disabled in your environment, and vice versa. This influences the protection rates, false alarm rates and system impact. The applied settings are used across all our Enterprise Tests over the year. That is to say, we do not allow a vendor to change settings depending on the test. Otherwise, vendors could e.g. configure their respective products for maximum protection in the protection tests (which would reduce performance and increase false alarms), and maximum speed in the performance tests (thus reducing protection and false alarms). Please not that some enterprise products have all their protection features disabled by default, so the admin has to configure the product to get any protection.

Below we have listed relevant deviations from default settings (i.e. setting changes applied by the vendors):

Acronis: “Backup”, “Vulnerability assessment”, “Patch management”, “Device control”, “Data Loss Prevention” and “Data protection map” disabled. “Third-party scan engine” enabled.

Avast: “Scan for potentially unwanted programs (PUPs)” was enabled in “File Shield”, “Web Shield” and “Mail Shield”.

Bitdefender: “Sandbox Analyzer” (for Applications and Documents) enabled. “Analysis mode” set to “Monitoring”. “Scan SSL” enabled for HTTP and RDP. “HyperDetect” and “Device Control” disabled. “Update ring” changed to “Fast ring”. “Web Traffic Scan” and “Email Traffic Scan” enabled for Incoming emails (POP3). “Ransomware Mitigation” enabled. “Process memory Scan” for “On-Access scanning” enabled. All “AMSI Command-Line Scanner” settings enabled for “Fileless Attack Protection”.

Cisco: “On Execute File and Process Scan” set to Active; “Exploit Prevention: Script Control” set to “Block”; “TETRA Deep Scan File” disabled; “Exclusions” set to “Microsoft Windows Default”; Engines “ETHIS”, “ETHOS”, “SPERO” and “Step-Up” disabled.

CrowdStrike: everything enabled and set to maximum, i.e. “Extra Aggressive”. “Sensor Visibility” for “Firmware” disabled. Uploading of “Unknown Detection-Related Executables” and “Unknown Executables” disabled.

Cybereason: “Anti-Malware” enabled; “Signatures mode” set to “Disinfect”; “Behavioral document protection” disabled; “Artificial intelligence” and “Anti-Exploit” set to “Moderate”; “Exploit protection”, “PowerShell and .NET”, “Anti-Ransomware” and “App Control” enabled and set to “Prevent”; “Exploit protection set to “Cautious”; all “Collection features” enabled; “Scan archives on access” enabled; Update interval set to 1 minute.

Elastic: MalwareScore (“windows.advanced.malware.threshold”) set to “aggressive”.

ESET: All “Real-Time & Machine Learning Protection” settings set to “Aggressive”.

G Data: “BEAST Behavior Monitoring” set to “Halt program and move to quarantine”. “G DATA WebProtection” add-on for Google Chrome installed and activated. “Malware Information Initiative” enabled.

Kaspersky: “Adaptive Anomaly Control” disabled; “Detect other software that can be used by criminals to damage your computer or personal data” enabled;

Malwarebytes: “Expert System Algorithms”, “Block penetration testing attacks”, “Disable IE VB Scripting”, “Java Malicious Inbound/outbound Shell Protection”, “Earlier RTP blocking”, “Enhanced sandbox protection” and “Thorough scan” enabled; “RET ROP Gadget detection”, “Malicious LoadLibrary Protection” and “Protected applications” enabled for all applications; “Protection for MessageBox Payload” enabled for MS Office; “Malwarebytes Browser Guard” Chrome extension enabled.

Microsoft: Google Chrome extension “Windows Defender Browser Protection” installed and enabled; “CloudExtendedTimeOut” set to 55; “PuaMode” enabled.

Sophos: “Threat Case creation” and “Web Control” disabled.

Trellix: “Real-Time Indicator Detection” disabled, “Exploit Guard” and “Malware Protection” enabled.

VIPRE: “Firewall” and “IDS” enabled and set to “Block With Notify”.

VMware: policy set to “Advanced”.

K7, WatchGuard: default settings.
...

Full Report